What is the best 3D printer to buy?

How To: The Beginners Guide to ordering, assembling, up…

I got a new printer!!! Tevo Tarantula Upgrades

Terrain Guide : Necromunda Armageddon

This is thesecond partof the series for purchasing a new 3D printer.If you missed the first part, go here. This is the list of common printers with my impressions and opinions on the different printers out there.

For the Wargame enthusiast, there are a number of great printers on the market. Depending on how you answered the questions above, there is probably a printer that is right for you. Ill list the Terrain printers first, by price, from lowest to highest, and put some tags following them with other details to help answer your 5 questions. Please not this is NOT an exhaustive list, and I will provide affiliate links to stores if you happen to choose a printer to buy. These help support the site, but in no way cost you more money.

There are further notes at the end of this article, but it was written because this is the 1 question I see coming from people interested in getting into 3D Terrain Printing. Here is a list of printers that you should look at, based on your specific needs. Once you narrow it down to a couple of printers, look online (Reddit, Facebook, Thingiverse) at the communities that support these printers. That is 100% the reason that I went with the Tevo Tarantula over the Anet as my first printer.

Cheat Sheet The Primary Questions:

What is the use? [Miniatures, Terrain]

What is my budget? [Low (Below $400), Medium ($400 $600), High ($600+)]

What is my technical skill? (If it is low, choose a pre-built) [Low, Competent, High]

What build size do I need? [Small (120120), Medium (200200), Large (300300), Huge (400400 +)

What Technology is used? [FDM, DLP, SLA]

(Please note, I mention the printer, where you can purchase it, a quick breakdown of what kind of printer it is, based on the questions above, my thoughts on the printer, and then links to reputable community resources to get a 2nd or even 3rd opinion)

Monoprice Select Mini (Amazon) / Creality3D CR-7 (Gearbest) /Cocoon (Cocoon AU)[1:Terrain, 2:Low, 3:Low, 4:Low, 5: FDM] : These style of printers are pre-built, small build volume, but inexpensive printers. A lot of people have good things to say about these printers. (I believe the 3 listed above are rebrands of the same printer.) (JAT.MNMakers Muse)

Tevo Tarantula () (Note: Amazon link is not cheapest) [1:Terrain, 2:Low, 3:Competent, 4:Medium+, 5: FDM] : This is the printer I use.I put together a guide on the printerthat goes through what it takes to buy, build, upgrade, etc this printer though, many of the links work for any i3 style printer. These printers use acrylic which works, but is not optimal. You can print most of the upgrades needed, or purchase aluminum or carbon fiber ones. This printer has a great basis to start from, giving you the ability to take a fairly mediocre printer into a very high quality printer. Up to this point, all of the terrain on the site was printed on my Tarantula. I think this is a great printer and there is a very large community to help with problems and upgrades. I think this printer has the best bang for the buck of the i3 printers especially the larger 280mm long bed. But, that does require a number of upgrades.

Anycubic Mega i3 () [1:Terrain, 2:Low, 3:Low, 4:Medium, 5: FDM] : These printers are a littler nicer in my view. They have an integrated filament run-out sensor and can recover from a power outage. This printer looks like a solid printer with a decent bed. It is not as cheap as the two printers above, but it is still not too expensive. This is a printer that should be anyones list. (3D Maker NoobCHEP 3D PrintingI talk more about Anycubic Printers here.

Tevo Tornado () [1:Terrain, 2:Low/Medium, 3:Low, 4:Large, 5: FDM] : This is a newer printer from Tevo. It is designed as a CR-10 killer. It really has been a success in this. It has a large bed allowing for larger prints. It has some features that set it above the CR-10 and seems like a great printer especially for the price point. Ive alsoput together a guide on the Tevo Tornado, though I do not own one. (Rui Raptor3D Maker NoobRui Raptor Cost to RunMakerfun 3D Tevo Tornado Preview).

CR-10 () [1:Terrain, 2:Low/Medium, 3:Low, 4:Large, 5: FDM] : The CR-10 came onto the scene earlier this year. They are a larger bed printer (300300) and there are even much larger beds than 300300 if you need up to a 500500 mm bed (at a higher cost). You can purchase the standard version, or the upgraded version that has a dual Z screw. The advantage of the CR-10 is the active community that helps support it, and out of the box it is a good printer. (JAT.MN3D Printing Nerd)

CR-10s () [1:Terrain, 2:Low/Medium, 3:Low, 4:Large, 5: FDM] : The CR-10s is the latest refinement to the CR-10. It includes updates such as dual Z, more memory, filament run out sensor (that may work), and power off recovery. The CR-10s has a 300x300x400 mm build volume giving you a huge range of what you can build. Out of the box, this thing just prints really well. (My Review)

Monoprice Maker Select Ultimate (Amazon) [1:Terrain, 2:Medium, 3:Low, 4:Medium, 5: FDM] : This is another one of those printers that is solid out of box. This one can be easily closed off to print ABS if that is an issue for you. You can get some ideas on how well it will print by looking at the Amazon reviews. This one I have heard good from, but not one I hear a lot about.

East 3D Gecko () [1:Terrain, 2:High, 3:High, 4:Large, 5: FDM] : This is my latest printer. It is a Core XY style printer. It is a very rigid machine and very interesting. I do recommend this with some reservations. The printer is still receiving a few updates from the manufacturer. As some issues have come up, East 3D has been upgrading this printer. The next upgrade I think will fix the majority of the issues. East 3D and others are very active on the Facebook group asking questions and coming up with some updates. There are videos showing super high speed printing by maker as well. Having an active group with very active and dedicated management means a lot to me. I like the printer as it is, but with the new updates coming soon, I think this will be a tough printer to beat at the price point. It is a kit though, and requires some skills to build.My preview and Printer information posts.

Prusa i3 Mk3 (Prusa) [1:Terrain, 2:High, 3:Competent/Low, 4:Medium+, 5: FDM] : This is one of the most popular and probably most refined i3 printers on the market. The Mk3 has just been announced and features a number of user friendly and recovery features that other consumer printers do not possess. If you can afford it, this is probably the printer you want to pick up. It has a very large community to help support it, and most of the i3 printers are clones this printer. If you want a pre-built printer, they offer those as well, at a higher price than the kit printer. (Thomas Sanladerer3D Printing Nerd)

FlashForge 3D Printer Creator Pro (Amazon) [1:Terrain, 2:High, 3:Low, 4:Small+, 5: FDM] : This printer is fully enclosed allowing the printing of ABS easily. The build volume is not quite Medium, but is definately larger than most small print volumes. This printer gets great reviews and I have heard many people comment on their quality. (3D Printing Nerd)

Delta Style Printers More Advanced

Monoprice Mini Delta (Not Yet Available) [1:Terrain, 2:Low, 3:Low, 4:Small, 5: FDM] : This printer was released via Indigogo. I am putting this here more as a placeholder. I have read that people are very interested int his printer and will update this entry as they become widely available.

Anycubic Kossel Delta () [1:Terrain, 2:Low, 3:Competent, 4:Small, 5: FDM] : This is a printer I have heard some good about. For the price, it sounds like a terrific value. This is a Delta printer, allowing you to print at a faster rate than cartesian printers. It is a little on the smaller side so that is something to keep in mind on the circular build plate. These are especially good for more circular based prints. (Press ResetI talk more about Anycubic Printers here.

FLSUN Linear Guide Version 3D Printer () [1:Terrain, 2:Low, 3:Competent, 4:Small/Medium, 5: FDM] : Here is another Delta that I see people talk about regularly. You can look at the reviews on Amazon. I recommend the Linear Rail version, and has a good sized print bed for a Delta printer. This is a little older, and I think I would personally go for the Anycubic Kossel printer over this one.

Tevo Little Monster () [1:Terrain, 2:High, 3:Competent, 4:Large, 5: FDM] : If you are looking for a Delta style printer, this is probably the best bet. It is an expensive printer but is large for a Delta. This printer has received some good reviews online, and people seem impressed by its capabilities. (3d Maker Noob)

Resin Based Printers SLA / DLP Advanced Printing

Micromake L2 (AliExpress Official Store) [1:Miniatures, 2:Medium, 3:Competent, 4:Small, 5: DLP] : This looks like another Wanhao Duplicator 7 clone. It is brand new, so I dont have any other information than what is on the store page. I am including it here to try and get a more complete view of 3D Resin printers and maybe in the future it will prove to be a great DLP printer. Ive startedcompiling information about the Micromake L2. Ive been reading some very positive reviews and it seems like a solid DLP printer.

Anycubic Photon (AliExpress Official Store) [1:Miniatures, 2:Medium, 3:Competent, 4:Small, 5: DLP] This is the latest printer from Anycubic and is also a DLP. This is likely going to be very comparable to the Tevo Firefly, being a copy of the popular Wanhao Duplicator 7 and comes with a screen interface.I talk more about Anycubic Printers here. As I collect more information about theAnycubic Photon, Ill post it here.

Wanhao Duplicator 7 () [1:Miniatures, 2:Medium, 3:Competent, 4:Small, 5: DLP] : This printer changed things earlier this year. This was the first low cost resin printer to reach the market. Wanhao has gone through several iterations and is currently at version 1.4. They have also just released the Wanhao 7 Plus that is a bit more expensive but has a nice upgrade that upgrades to the touch screen. If you need an inexpensive resin printer, today, this is probably your best bet. When the Firefly is available, it will be worth looking at what it offers. Ive read mixed reviews overall on this, but there is a very active Facebook group to help new people out. This would not make for a good first printer.

Tevo Firefly (Not Yet Available) [1:Miniatures, 2:Medium, 3:Competent, 4:Small, 5: DLP] : This is thelatest printer from Tevo, and is DLP. It is a lower cost alternative to the Wanhao Duplicator 7. It has not been released yet and this is a placeholder location.

Peopoly Moai (Peopoly) [1:Miniatures, 2:High, 3:Competent, 4:Small, 5: SLA] : The Peopoly Moai came to us via Kickstarter and proved to be popular. It has since been released to the market and gets good reviews. It is the lowest cost SLA printer on the list, which means it is still a pretty expensive printer, in consumer pricing terms. This is a great printer for printing miniatures with high detail. (Greg_FLMakers Muse Pre Production Unit)

Formlabs Form 2 [1:Miniatures, 2:Very High, 3:Competent, 4:Small, 5: SLA] : The Form 2 is used by a great number of people. This is a great printer, but it comes at a very high price. This is outside the range for most of us, but I figured I would add it to show the beginning of the more pro market for 3D Printers. (Makers Muse)

There you have it. A very non-exhaustive list full of my personal opinions on these printers. Out of all of these printers listed, I only own two of them, but I do follow pretty closely a large number of them and there is a large maker community that produces content about the printers that I also read and watch. This entire list is based off of my opinion and I am sure that there will be a lot of dissenting opinions. I tried to back up my opinions with links tocontent creators I personally trust.

I tried to pick the lowest cost / best value links. As an example in the FLSUN links, I pointed to the linear Rail versions since they are higher quality. If money is more of a concern, some of these printers have a cheaper version available that have corners cut to reduce the price. For a first printer, I would recommend either an i3 clone kit, or a pre built printer. (Or, mostly built printer, like the CR-10s) Also, be aware, I am a bit biased towards Tevo. I believe they have a good product and like that the owner is active in the community. On the East 3D Geko side, that is the reason I was so interested in that printer, because of the involvement of the company owner. This is also why I attempted to find reputable reviews by others on the printers I recommend in this guide. If you have any constructive comments or questions, please leave them below or contact me directly. My printer was purchased to print 3D terrain and Dungeon tiles, primarily, and is also the genesis of this sites growth in the coverage of those topics.

After you order your printer,check out the resources in the directoryfor terrain models, miniatures models and more. It contains links to the modelers sites themselves as well as my curated collection on Thingiverse. Ive also talked aboutother things neededfor FDM printers and a similar guide forResin based Printers. There are also other guides, like setting upOctoprint on a Raspberry Pi(which I highly recommend). I alsotalk about slicingand getting your first print job done on your printer. Have a look around at the other articles I have posted.

Ive been a technologist pretty much my entire life. I got my first computer at the age of 12, while most other kids only knew computers as the giant machines shown in movies. It sparked an interest that has led me into IT work for a living. This new 3D Printing hobby is an extension of my technologist tendencies. I like to play with new technologies.

How to Choose the Best 3D Printer for 3D Printable Terrain Maker Fun 3D – 3D Printing and Terrain- [] choosing a printer, and then the basic concepts and styles of 3D printers themselves. The next part of the

ANYCUBIC 3D Printers: Quality at low cost Maker Fun 3D – 3D Printing and Terrain- [] comes mostly assembled and tested. This is one of the printers I talk about in my 3D buying Guide because

New CoreXY Printer: East 3D Gecko Maker Fun 3D – 3D Printing and Terrain- [] I discuss this printer in my 3D Printer Buying Guide: []

Creality CR-10s Review – The Hype is Real Maker Fun 3D – 3D Printing and Terrain- [] Let me start out with The hype is real. Seriously, the Creality CR-10s has earned its reputation as an

Your email address will not be published.Required fields are marked*

Notify me of follow-up comments by email.

World War Tesla Parts Needed for Units

3D Printing Deals from Amazon, Gearbest and Elsewhere

Infographic: 3D Printing Filament Comparison

Designed byElegant ThemesPowered byWordPress

Post Created 739

Related Posts

Begin typing your search above and press enter to search. Press ESC to cancel.

Back To Top